1465 lines
63 KiB
INI
1465 lines
63 KiB
INI
#!version:1.0.0.1
|
||
|
||
##File header "#!version:1.0.0.1" can not be edited or deleted, and must be placed in the first line.##
|
||
##This template file is applicable to SIP-T28P/T26P/T22P/T20P/T21P/T19P/T46G/T42G/T41P IP phones running firmware version 72 or later.##
|
||
##For more information on configuration parameters, refer to Yealink_SIP-T2_Series_T19P_T4_Series_IP_Phones_Auto_Provisioning_Guide.##
|
||
|
||
#######################################################################################
|
||
## Hostname ##
|
||
#######################################################################################
|
||
network.dhcp_host_name =
|
||
|
||
#######################################################################################
|
||
## PPPoE(Except T41P/T42G Models) ##
|
||
#######################################################################################
|
||
network.pppoe.user =
|
||
network.pppoe.password =
|
||
|
||
|
||
#######################################################################################
|
||
## Network Advanced ##
|
||
#######################################################################################
|
||
##It enables or disables the PC port.0-Disabled,1-Auto Negotiation.
|
||
##The default value is 1.It takes effect after a reboot.
|
||
network.pc_port.enable =
|
||
|
||
##It configures the transmission mode and speed of the Internet (WAN) port.
|
||
##0-Auto negotiate
|
||
##1-Full duplex 10Mbps
|
||
##2-Full duplex 100Mbps
|
||
##3-Half duplex 10Mbps
|
||
##4-Half duplex 100Mbps
|
||
##5-Full duplex 1000Mbps (only applicable to SIP-T42G and SIP-T46G IP phones)
|
||
##The default value is 0.It takes effect after a reboot.
|
||
network.internet_port.speed_duplex =
|
||
|
||
##It configures the transmission mode and speed of the PC (LAN) port.
|
||
##0-Auto negotiate
|
||
##1-Full duplex 10Mbps
|
||
##2-Full duplex 100Mbps
|
||
##3-Half duplex 10Mbps
|
||
##4-Half duplex 100Mbps
|
||
##5-Full duplex 1000Mbps (only applicable to SIP-T42G and SIP-T46G IP phones)
|
||
##The default value is 0.It takes effect after a reboot.
|
||
network.pc_port.speed_duplex =
|
||
|
||
##It enables or disables the phone to use manually configured static IPv4 DNS when Internet (WAN) port type for IPv4 is configured as DHCP.
|
||
##0-Disabled (use the IPv4 DNS obtained by DHCP) 1-Enabled
|
||
##The default value is 0.It takes effect after a reboot.
|
||
network.static_dns_enable =
|
||
|
||
network.ipv6_static_dns_enable =
|
||
|
||
###Only T41P/T42G/T46G Models support this parameter
|
||
network.vlan.pc_port_mode =
|
||
##It enable or disable to use A record of TTL
|
||
##The defalue value is 1;0-Disable 1-Enable
|
||
|
||
network.dns.ttl_enable =
|
||
##It configures the LAN MTU (Except T21D/T19D)
|
||
##The default value is 1500,.Integer from 128 to 1500.It takes effect after a reboot.
|
||
network.mtu_value =
|
||
|
||
|
||
#######################################################################################
|
||
## VLAN ##
|
||
#######################################################################################
|
||
network.vlan.internet_port_enable =
|
||
network.vlan.internet_port_vid =
|
||
network.vlan.internet_port_priority =
|
||
network.vlan.pc_port_enable =
|
||
network.vlan.pc_port_vid =
|
||
network.vlan.pc_port_priority =
|
||
network.vlan.dhcp_enable =
|
||
network.vlan.dhcp_option =
|
||
##It configures LLDP or manually VLAN can't obtain IP, whether to switch to other methods of VLAN or closed VLAN to get IP
|
||
##(Except T19P/T21P Models) 0-Disable 1-Enable
|
||
network.vlan.vlan_change.enable =
|
||
|
||
#######################################################################################
|
||
## WEB Port ##
|
||
#######################################################################################
|
||
##It configures the HTTP port for web server access.
|
||
##The default value is 80.It takes effect after a reboot.
|
||
network.port.http =
|
||
|
||
##It configures the HTTPS port for web server access.
|
||
##The default value is 443.It takes effect after a reboot.
|
||
network.port.https =
|
||
|
||
wui.https_enable =
|
||
wui.http_enable =
|
||
|
||
#######################################################################################
|
||
## QoS ##
|
||
#######################################################################################
|
||
##It configures the voice QoS.
|
||
##The default value is 46.It takes effect after a reboot.Integer from 0 to 63
|
||
network.qos.rtptos =
|
||
|
||
##It configures the SIP QoS.
|
||
##The default value is 26.It takes effect after a reboot.Integer from 0 to 63
|
||
network.qos.signaltos =
|
||
|
||
#######################################################################################
|
||
## 802.1X ##
|
||
#######################################################################################
|
||
network.802_1x.mode =
|
||
network.802_1x.identity =
|
||
network.802_1x.md5_password =
|
||
network.802_1x.root_cert_url =
|
||
network.802_1x.client_cert_url =
|
||
|
||
##It configure the mouth of the PC 802.1 x - logoff function.It takes effect after a reboot.
|
||
##The default value is 0-Dsable , 1-Enable
|
||
network.802_1x.proxy_eap_logoff.enable =
|
||
#######################################################################################
|
||
## OpenVPN(Except T19P Model) ##
|
||
#######################################################################################
|
||
network.vpn_enable =
|
||
openvpn.url =
|
||
|
||
#######################################################################################
|
||
## LLDP ##
|
||
#######################################################################################
|
||
network.lldp.enable =
|
||
network.lldp.packet_interval =
|
||
|
||
#######################################################################################
|
||
## CDP ##
|
||
#######################################################################################
|
||
network.cdp.enable =
|
||
network.cdp.packet_interval =
|
||
|
||
#######################################################################################
|
||
## Span to PC ##
|
||
#######################################################################################
|
||
network.span_to_pc_port =
|
||
|
||
#######################################################################################
|
||
## RTP Port ##
|
||
#######################################################################################
|
||
##It configures the maximum local RTP port.
|
||
##The default value is 11800.It takes effect after a reboot.Integer from 1024 to 65535
|
||
network.port.max_rtpport =
|
||
|
||
##It configures the maximum local RTP port.
|
||
##The default value is 11780.It takes effect after a reboot.Integer from 1024 to 65535
|
||
network.port.min_rtpport =
|
||
|
||
#######################################################################################
|
||
## Syslog ##
|
||
#######################################################################################
|
||
syslog.mode =
|
||
|
||
##It configures the IP address or domain name of the syslog server when exporting log to the syslog server.
|
||
##It takes effect only if the parameter <20><>syslog.mode<64><65> is configured as Server.
|
||
##The default value is blank.It takes effect after a reboot.
|
||
syslog.server =
|
||
|
||
##It configures the detail level of syslog information to be exported.0 means nothing and 6 means all.
|
||
##The default value is 3.It takes effect after a reboot.Integer from 0 to 6
|
||
syslog.log_level =
|
||
|
||
#######################################################################################
|
||
## TR069(Except T41P/T42G Models) ##
|
||
#######################################################################################
|
||
managementserver.enable =
|
||
managementserver.username =
|
||
managementserver.password =
|
||
managementserver.url =
|
||
managementserver.connection_request_username =
|
||
managementserver.connection_request_password =
|
||
managementserver.periodic_inform_enable =
|
||
managementserver.periodic_inform_interval =
|
||
|
||
#######################################################################################
|
||
## Autoprovision ## ##
|
||
#######################################################################################
|
||
### It enables or disables the phone to synchronize personalized configuration settings with the auto provisioning server.
|
||
### If it is set to 1 (Enabled), personalized configuration settings via web/phone user interface are saved in the MAC-local.cfg file on the phone,
|
||
### and then the phone will upload the MAC-local.cfg file to the provisioning server. During auto provisioning, the phone requests to download the MAC-local.cfg file on the provisioning server.
|
||
### 0-Disabled, 1-Enabled. The default value is 0.
|
||
auto_provision.custom.sync =
|
||
|
||
### It enables or disables the phone to protect personalized configuration settings even after auto provisioning.
|
||
### If it is set to 1 (Enabled), personalized configuration settings via web/phone user interface will be protected and remained after auto provisioning.
|
||
### 0-Disabled, 1-Enabled. The default value is 0.
|
||
auto_provision.custom.protect =
|
||
|
||
auto_provision.custom.upload_method=
|
||
|
||
#######################################################################################
|
||
## Autop Mode ##
|
||
#######################################################################################
|
||
auto_provision.power_on =
|
||
|
||
#######################################################################################
|
||
## Autop PNP ##
|
||
#######################################################################################
|
||
auto_provision.pnp_enable =
|
||
|
||
#######################################################################################
|
||
## Autop DHCP ##
|
||
#######################################################################################
|
||
auto_provision.dhcp_option.enable =
|
||
auto_provision.dhcp_option.list_user_options =
|
||
|
||
#######################################################################################
|
||
## Autop Repeat ##
|
||
#######################################################################################
|
||
auto_provision.repeat.enable =
|
||
auto_provision.repeat.minutes =
|
||
|
||
#######################################################################################
|
||
## Autop Weekly ##
|
||
#######################################################################################
|
||
auto_provision.weekly.enable =
|
||
auto_provision.weekly.dayofweek =
|
||
auto_provision.weekly.begin_time =
|
||
auto_provision.weekly.end_time =
|
||
|
||
#######################################################################################
|
||
## Autop URL ##
|
||
#######################################################################################
|
||
auto_provision.server.url =
|
||
auto_provision.server.username =
|
||
auto_provision.server.password =
|
||
|
||
#######################################################################################
|
||
## Autop AES Key ##
|
||
#######################################################################################
|
||
##It configures the AES key for decrypting the Common CFG file. The valid characters contain: 0 ~ 9, A ~ Z, a ~ z.
|
||
##The default value is blank.
|
||
auto_provision.aes_key_16.com =
|
||
|
||
##It configures the AES key for decrypting the MAC-Oriented CFG file. The valid characters contain: 0 ~ 9, A ~ Z, a ~ z.
|
||
##The default value is blank.
|
||
auto_provision.aes_key_16.mac =
|
||
|
||
auto_provision.aes_key_in_file =
|
||
|
||
##It configures the access URL of the custom MAC-Oriented CFG file.
|
||
##The default value is blank.
|
||
custom_mac_cfg.url =
|
||
|
||
##It configures the value (vendor name of the device) of DHCP option 60.
|
||
##The default value is yealink.
|
||
auto_provision.dhcp_option.option60_value =
|
||
|
||
|
||
|
||
#######################################################################################
|
||
## Autop wildcard ##
|
||
#######################################################################################
|
||
|
||
auto_provision.url_wildcard.pn =
|
||
|
||
#######################################################################################
|
||
## Autop Code ##
|
||
#######################################################################################
|
||
##It configures the name of the code for triggering auto provisioning.
|
||
##The default value is blank.It takes effect after a reboot.
|
||
autoprovision.1.name =
|
||
|
||
##It configures the code for triggering auto provisioning.
|
||
##Valid characters are digits, # and *.Example:autoprovision.1.code = *99The default value is blank.
|
||
##It takes effect after a reboot.
|
||
autoprovision.1.code =
|
||
|
||
##It configures the access URL of auto provisioning server.The default value is blank.
|
||
##It takes effect after a reboot.
|
||
autoprovision.1.url =
|
||
|
||
##It configures the user name for authentication during auto provisioning.
|
||
##The default value is blank.It takes effect after a reboot.
|
||
autoprovision.1.user =
|
||
|
||
##It configures the password for authentication during auto provisioning.
|
||
##The default value is blank.It takes effect after a reboot.
|
||
autoprovision.1.password =
|
||
|
||
##It configures the AES key for decrypting the Common CFG file.
|
||
##The default value is blank.It takes effect after a reboot.
|
||
autoprovision.1.com_aes =
|
||
|
||
##It configures the AES key for decrypting the MAC-Oriented CFG file.
|
||
##The default value is blank.It takes effect after a reboot.
|
||
autoprovision.1.mac_aes =
|
||
|
||
#######################################################################################
|
||
## Watch Dog ##
|
||
#######################################################################################
|
||
watch_dog.enable =
|
||
|
||
#######################################################################################
|
||
## SIP Advanced ##
|
||
#######################################################################################
|
||
sip.use_23_as_pound =
|
||
sip.rfc2543_hold =
|
||
sip.use_out_bound_in_dialog =
|
||
sip.reg_surge_prevention =
|
||
sip.send_response_by_request =
|
||
sip.notify_reboot_enable =
|
||
sip.disp_incall_to_info =
|
||
sip.limit_server_name =
|
||
sip.limit_server_reason =
|
||
sip.listen_port =
|
||
sip.tls_listen_port =
|
||
sip.trust_ctrl =
|
||
sip.nat_stun.enable =
|
||
sip.nat_stun.server =
|
||
sip.nat_stun.port =
|
||
sip.timer_t1 =
|
||
sip.timer_t2 =
|
||
sip.timer_t4 =
|
||
custom.features.redial_via_local_sip_server.enable =
|
||
|
||
|
||
##It is XSI authentication mode.0-Disable 1-Enable (Except T19P/T21P Models)
|
||
sip.authentication_for_xsi =
|
||
##It is DSS KEY to call park type, whether the trigger BLF function.It takes effect after a reboot.
|
||
##The default value is 0-Disable(DSS KEY to call park type,triggering BLF function) 1-Enable
|
||
sip.call_park_without_blf =
|
||
##It is ASCII conversion into corresponding symbols.
|
||
##The defalult value is blank. 0-Disable 1-Enable
|
||
sip.escape_characters.enable =
|
||
##The default value is 0 ( said according to the transmission mode configured to listen on port),1-
|
||
##1-said at the same time to monitor TCP and UDP
|
||
##2-said to monitor TCP and UDP at the same time, and from the BLF - the LIST to subscribe to the contact with a transport = TCP parameters
|
||
sip.listen_mode =
|
||
##The default value is 0-Disable, 1-Enable.It takes effect after a reboot.
|
||
##0-registered according to the uri of the tectonic refer - by domain
|
||
##1-according to refer the from header fields to construct refer - by domain
|
||
|
||
sip.refer_by_header_auto_build =
|
||
##The default is blank.The Valid characters are digits - _.! ~ * # '() & Q462 = + R452 $,;?/ \ 0
|
||
##It is username needs to be preserved in a special notation.
|
||
sip.reserve_characters =
|
||
##The default value is 0.(contracting out the random contact, via port to carry fixed port).It takes effect after a reboot.
|
||
##1-the out-contracting port random contact, via port to carry
|
||
##2-the out-contracting ports fixed contact, via carry fix
|
||
sip.tcp_port_random_mode =
|
||
|
||
|
||
#######################################################################################
|
||
## Echo Cancellation ##
|
||
#######################################################################################
|
||
voice.vad =
|
||
voice.cng =
|
||
voice.echo_cancellation =
|
||
voice.call_preview_mode =
|
||
|
||
#######################################################################################
|
||
## Jitter Buffer ##
|
||
#######################################################################################
|
||
voice.jib.adaptive =
|
||
voice.jib.min =
|
||
voice.jib.max =
|
||
voice.jib.normal =
|
||
|
||
#######################################################################################
|
||
## Tones ##
|
||
#######################################################################################
|
||
voice.tone.country =
|
||
voice.tone.dial =
|
||
voice.tone.ring =
|
||
voice.tone.busy =
|
||
voice.tone.congestion =
|
||
voice.tone.callwaiting =
|
||
voice.tone.dialrecall =
|
||
voice.tone.info =
|
||
voice.tone.stutter =
|
||
voice.tone.autoanswer =
|
||
voice.tone.message =
|
||
|
||
#######################################################################################
|
||
## Volume ##
|
||
#######################################################################################
|
||
voice.handfree.spk_vol =
|
||
voice.handfree.tone_vol =
|
||
voice.handset.spk_vol =
|
||
voice.handset.tone_vol =
|
||
voice.headset.spk_vol =
|
||
voice.headset.tone_vol =
|
||
voice.ring_vol=
|
||
voice.group_spk_vol =
|
||
|
||
### Only T28P/T26P/T22P/T20P Models support the three parameters
|
||
voice.handfree_send =
|
||
voice.handset_send =
|
||
voice.headset_send =
|
||
|
||
#######################################################################################
|
||
## Transfer ##
|
||
#######################################################################################
|
||
##It enables or disables the transferee party<74><79>s phone to prompt a missed call on the LCD screen before displaying
|
||
##the caller ID when performing a semi-attended transfer.0-Enabled,1-Disabled
|
||
##The default value is 1.
|
||
transfer.semi_attend_tran_enable =
|
||
|
||
##It enables or disables the phone to complete the blind transfer through on-hook.0-Disabled,1-Enabled .
|
||
##The default value is 1.
|
||
transfer.blind_tran_on_hook_enable =
|
||
|
||
##It enables or disables the phone to transfer call to the two parties after a local conference call hangs up.
|
||
##0-Disabled,1-Enabled.
|
||
##The default value is 0.
|
||
transfer.tran_others_after_conf_enable =
|
||
|
||
##It enables or disables the phone to complete the attended transfer through on-hook.
|
||
##0-Disabled,1-Enabled.
|
||
##The default value is 1.
|
||
transfer.on_hook_trans_enable =
|
||
|
||
##It configures the DSS key behavior during an active call when user presses the DSS
|
||
##key and the DSS key is configured as a speed dial, transfer or BLF/BLF list key.
|
||
##0-New Call,1-Attended Transfer,2-Blind Transfer.
|
||
##The default value is 2.
|
||
transfer.dsskey_deal_type =
|
||
|
||
###Except T20P/T41P/T42G/T46G Models
|
||
##It enables or disables the phone to enter Transfer to menu during multiple calls when pressing the transfer soft key or TRAN key.
|
||
##0-Disabled,1-Enabled.
|
||
##The default value is 1.
|
||
transfer.multi_call_trans_enable =
|
||
|
||
#######################################################################################
|
||
## Language Settings ##
|
||
#######################################################################################
|
||
##It configures the language of the web user interface.
|
||
##Chinese_S is only applicable to SIP-T19P, SIP-T21P and SIP-T46G IP phones.
|
||
##Chinese_T is only applicable to SIP-T46G IP phones.
|
||
##French, Portuguese and Spanish are not applicable to SIP-T19P and SIP-T21P IP phones.
|
||
lang.wui =
|
||
|
||
##It configures the language of the phone user interface.
|
||
##Chinese_S and Chinese_T are only applicable to SIP-T19P, SIP-T21P and SIP-T46G IP phones.
|
||
##The default value is English.
|
||
lang.gui =
|
||
|
||
gui_lang.url =
|
||
gui_lang.delete =
|
||
##Except T19P/T21P Models
|
||
wui_lang.url =
|
||
wui_lang_note.url =
|
||
wui_lang.delete =
|
||
|
||
#######################################################################################
|
||
## Auto Redial ##
|
||
#######################################################################################
|
||
auto_redial.enable =
|
||
auto_redial.interval =
|
||
auto_redial.times =
|
||
|
||
#######################################################################################
|
||
## Zero Touch ##
|
||
#######################################################################################
|
||
zero_touch.enable =
|
||
zero_touch.wait_time =
|
||
zero_touch.network_fail_wait_times =
|
||
zero_touch.network_fail_delay_times =
|
||
|
||
#######################################################################################
|
||
## Push XML ##
|
||
#######################################################################################
|
||
push_xml.server =
|
||
push_xml.block_in_calling=
|
||
push_xml.sip_notify=
|
||
|
||
#######################################################################################
|
||
## Dial Plan ##
|
||
#######################################################################################
|
||
dialplan.area_code.code =
|
||
dialplan.area_code.min_len =
|
||
dialplan.area_code.max_len =
|
||
dialplan.area_code.line_id =
|
||
|
||
### X ranges from 1 to 10
|
||
###dialplan.block_out.number.x =
|
||
###dialplan.block_out.line_id.x =
|
||
|
||
dialplan.block_out.number.1 =
|
||
dialplan.block_out.line_id.1 =
|
||
|
||
###X ranges from 1 to 100
|
||
###dialplan.dialnow.rule.X =
|
||
###dialplan.dialnow.line_id.X =
|
||
|
||
dialplan.dialnow.rule.1 =
|
||
dialplan.dialnow.line_id.1 =
|
||
|
||
###X ranges from 1 to 100
|
||
###dialplan.replace.prefix.X =
|
||
###dialplan.replace.replace.X =
|
||
###dialplan.replace.line_id.X =
|
||
|
||
dialplan.replace.prefix.1 =
|
||
dialplan.replace.replace.1 =
|
||
dialplan.replace.line_id.1 =
|
||
|
||
dialplan_dialnow.url =
|
||
phone_setting.dialnow_delay =
|
||
dialplan_replace_rule.url =
|
||
|
||
|
||
#######################################################################################
|
||
## Remote Phonebook(Except T20P Model) ##
|
||
#######################################################################################
|
||
###X ranges from 1 to 5
|
||
###remote_phonebook.data.X.url =
|
||
###remote_phonebook.data.X.name =
|
||
|
||
remote_phonebook.data.1.url =
|
||
remote_phonebook.data.1.name =
|
||
|
||
###Except T41P/T42G Models
|
||
remote_phonebook.display_name =
|
||
|
||
###It enables or disables the phone to update the data of the remote phone book at a time when accessing the remote phone book.
|
||
###0-Disabled, 1-Enabled. The default value is 0.(Except T19P/T21P Models)
|
||
features.remote_phonebook.enter_update_enable =
|
||
|
||
##It enables or disables the phone to perform a remote phone book search when receiving an incoming call.
|
||
##0-Disabled,1-Enabled.
|
||
##The default value is 0.
|
||
features.remote_phonebook.enable =
|
||
|
||
##It configures the interval (in seconds) for the phone to update the data of the remote phone book from the remote phone book server.
|
||
##The value 0 means the phone will not regularly update the data of the remote phone book from the remote phone book server.
|
||
##The default value is 21600.Integer from 3600 to 2592000,and 0.
|
||
features.remote_phonebook.flash_time =
|
||
|
||
#######################################################################################
|
||
## LDAP(Except T19P/T20P Models) ##
|
||
#######################################################################################
|
||
##It enables or disables LDAP feature.0-Disabled,1-Enabled.
|
||
##The default value is 0.
|
||
ldap.enable =
|
||
|
||
##It configures the criteria for searching the contact name attributes.
|
||
##Example:ldap.name_filter = (|(cn=%)(sn=%)).
|
||
##The default value is blank.
|
||
ldap.name_filter =
|
||
|
||
##It configures the criteria for searching the contact number attributes.
|
||
##Example:ldap.number_filter = (|(telephoneNumber=%)(mobile=%)(ipPhone=%))
|
||
##The default value is blank.
|
||
ldap.number_filter =
|
||
|
||
##It configures the IP address or domain name of the LDAP server.
|
||
##The default value is blank.
|
||
ldap.host =
|
||
|
||
##It configures the port of the LDAP server.
|
||
##The default value is 389.Integer from 1 to 65535.
|
||
ldap.port =
|
||
|
||
##It configures the LDAP search base which corresponds to the location of the LDAP phonebook.
|
||
##Example:ldap.base = dc=yealink,dc=cn.
|
||
##The default value is blank.
|
||
ldap.base =
|
||
|
||
##It configures the user name for accessing the LDAP server.
|
||
##The default value is blank.
|
||
ldap.user =
|
||
|
||
##It configures the password for accessing the LDAP server.
|
||
##The default value is blank.
|
||
ldap.password =
|
||
|
||
##It configures the maximum of the search results returned by the LDAP server to be displayed.
|
||
##The default value is 50.Integer from 1 to 32000.
|
||
ldap.max_hits =
|
||
|
||
##It configures the name attributes of each record to be returned by the LDAP server.
|
||
##Multiple attributes are separated by spaces.Example:ldap.name_attr =sn cn.
|
||
##The default value is blank.
|
||
ldap.name_attr =
|
||
|
||
##It configures the number attributes of each record to be returned by the LDAP server.
|
||
##Multiple attributes are separated by spaces.Example:ldap.numb_attr = Mobile ipPhone.
|
||
##The default value is blank.
|
||
ldap.numb_attr =
|
||
|
||
##It configures the display name of the contact record displayed on the LCD screen. The value of this parameter must start with <20><>%<25><> symbol.
|
||
##Example:ldap.display_name = %cn
|
||
##The default value is blank.
|
||
ldap.display_name =
|
||
|
||
##It configures the LDAP version.
|
||
##The default value is 3.
|
||
ldap.version =
|
||
|
||
##It enables or disables the phone to perform an LDAP search when receiving an incoming call.
|
||
##0-Disabled,1-Enabled.
|
||
##The default value is 0.
|
||
ldap.call_in_lookup =
|
||
|
||
##It enables or disables the phone to sort the search results in alphabetical order or numerical order.
|
||
##0-Disabled,1-Enabled.
|
||
##The default value is 0.
|
||
ldap.ldap_sort =
|
||
##It is the electricity + start, automatic search + 00 the beginning and the beginning of the numbe
|
||
##The default value is 0.(0-Disable,1-Enable )(Except T19P/T21P Models)
|
||
ldap.incoming_call_special_search.enable =
|
||
##The default value is 0,value of 0 to 2, respectively the ldap, ldap + StarTLS and ldaps
|
||
ldap.tls_mode =
|
||
ldap.call_out_lookup =
|
||
|
||
#######################################################################################
|
||
## Features ##
|
||
#######################################################################################
|
||
features.normal_refuse_code =
|
||
features.auto_answer_delay =
|
||
features.allow_mute =
|
||
features.group_listen_in_talking_enable =
|
||
features.call_completion_enable =
|
||
features.call_num_filter =
|
||
features.direct_ip_call_enable =
|
||
features.relog_offtime =
|
||
features.ringer_device.is_use_headset =
|
||
features.factory_pwd_enable =
|
||
features.anonymous_response_code =
|
||
features.export_cfg_erase_pwd =
|
||
features.show_action_uri_option =
|
||
features.reset_by_long_press_enable =
|
||
features.show_anywhere_remote_office_enable =
|
||
features.upload_server =
|
||
features.call_log_show_num =
|
||
features.ldap.input_type =
|
||
features.call_invite_format =
|
||
action_url.show_msgbox =
|
||
phone_setting.logon_wizard_forever_wait =
|
||
features.call_invite_format =
|
||
features.transfer_type =
|
||
features.caller_name_type_on_dialing =
|
||
phone_setting.unregister_account_block_out.enable=
|
||
gui_input_method.delete =
|
||
features.off_hook_answer.enable =
|
||
|
||
|
||
|
||
##Only for T46G Models support this parameter
|
||
features.block_linekey_in_menu.enable =
|
||
|
||
features.shorten_linekey_label.enable =
|
||
features.dsskey_blind_tran =
|
||
features.special_auto_answer_tone =
|
||
features.blf_pickup_only_send_code =
|
||
features.display_method_on_dialing =
|
||
|
||
|
||
##It is configured in the middle of the screen shows the current default at the bottom of the account name.
|
||
##The default is 0.CNT version 1.
|
||
features.show_default_account=
|
||
|
||
## Except T4X Models support this
|
||
features.reboot_in_talk_enable =
|
||
|
||
## Except T19P/T21P Models support this
|
||
features.barge_in_via_username.enable =
|
||
|
||
features.flash_url_dsskey_led.enable =
|
||
features.default_account =
|
||
features.forward_call_popup.enable =
|
||
features.linekey_call_with_default_account =
|
||
features.missed_call_popup.enable =
|
||
features.text_message_popup.enable =
|
||
features.voice_mail_popup.enable =
|
||
features.hide_feature_access_codes.enable =
|
||
|
||
## Except T19P/T21P/T4X Models support this
|
||
features.hide_caller_id.enable =
|
||
|
||
## Only for T4X Models support this parameter
|
||
features.hide_zero_touch_url.enable =
|
||
|
||
## Only T46G Models support this parameter
|
||
features.config_dsskey_length =
|
||
|
||
|
||
|
||
#######################################################################################
|
||
## Features Forward ##
|
||
#######################################################################################
|
||
|
||
###Except T19P Model
|
||
features.fwd_mode =
|
||
|
||
features.fwd_diversion_enable =
|
||
|
||
#######################################################################################
|
||
## Features DND ##
|
||
#######################################################################################
|
||
|
||
###Except T19P Model
|
||
features.dnd_mode =
|
||
|
||
features.dnd.enable =
|
||
features.dnd.on_code =
|
||
features.dnd.off_code =
|
||
features.dnd_refuse_code =
|
||
features.dnd.emergency_enable =
|
||
features.dnd.emergency_authorized_number =
|
||
|
||
#######################################################################################
|
||
## Features Bluetooth(Only for T46G model) ##
|
||
#######################################################################################
|
||
features.bluetooth_enable =
|
||
|
||
#######################################################################################
|
||
## Features BLF ##
|
||
#######################################################################################
|
||
##It configures BLF LED mode and provides four kinds of definition for the BLF/BLF list key LED status.
|
||
##For more information, refer to BLF LED Mode on page 218.
|
||
##The default value is 0.
|
||
features.blf_led_mode =
|
||
|
||
##It enables or disables the phone to deal with the Version header in the BLF NOTIFY message sent by the server.
|
||
##0-Disabled,1-Enabled.
|
||
##The default value is 0.It takes effect after a reboot.
|
||
features.blf_list_version =
|
||
|
||
#######################################################################################
|
||
## Features Intercom ##
|
||
#######################################################################################
|
||
features.intercom.allow =
|
||
features.intercom.mute =
|
||
features.intercom.tone =
|
||
features.intercom.barge =
|
||
|
||
#######################################################################################
|
||
## Features Hotline ##
|
||
#######################################################################################
|
||
##It configures the hotline number.
|
||
##The default value is blank.
|
||
features.hotline_number =
|
||
|
||
##It configures the delay time (in seconds) for the phone to dial out the hotline number automatically.
|
||
##The default value of delay time is 4.Integer from 0 to 10
|
||
features.hotline_delay =
|
||
|
||
#######################################################################################
|
||
## Features DTMF ##
|
||
#######################################################################################
|
||
features.dtmf.hide =
|
||
|
||
###Except T20P Model
|
||
features.dtmf.hide_delay =
|
||
|
||
features.dtmf.repetition =
|
||
features.dtmf.transfer =
|
||
features.dtmf.replace_tran =
|
||
features.dtmf.duration =
|
||
features.dtmf.volume =
|
||
|
||
#######################################################################################
|
||
## Features Audio Settings ##
|
||
#######################################################################################
|
||
features.headset_prior =
|
||
|
||
###Except T19P/T21P Models
|
||
features.headset_training =
|
||
features.alert_info_tone =
|
||
features.busy_tone_delay =
|
||
features.send_pound_key =
|
||
features.key_as_send =
|
||
features.send_key_tone =
|
||
features.key_tone =
|
||
features.play_hold_tone.enable =
|
||
features.play_hold_tone.delay =
|
||
features.redial_tone =
|
||
features.partition_tone =
|
||
|
||
#######################################################################################
|
||
## Features Action URI ##
|
||
#######################################################################################
|
||
features.action_uri_limit_ip =
|
||
|
||
|
||
#######################################################################################
|
||
## Features Prefix ##
|
||
#######################################################################################
|
||
features.password_dial.enable =
|
||
features.password_dial.prefix =
|
||
features.password_dial.length =
|
||
|
||
#######################################################################################
|
||
## Features History ##
|
||
#######################################################################################
|
||
features.save_call_history =
|
||
|
||
#######################################################################################
|
||
## Notification Popups ##
|
||
#######################################################################################
|
||
features.voice_mail_popup.enable=
|
||
features.missed_call_popup.enable=
|
||
features.forward_call_popup.enable=
|
||
features.text_message_popup.enable=
|
||
|
||
#######################################################################################
|
||
## Ringtone ##
|
||
#######################################################################################
|
||
ringtone.url =
|
||
ringtone.delete =
|
||
|
||
#######################################################################################
|
||
## Phone Settings ##
|
||
#######################################################################################
|
||
phone_setting.inter_digit_time =
|
||
phone_setting.ring_type =
|
||
|
||
phone_setting.ring_for_tranfailed =
|
||
phone_setting.is_deal180 =
|
||
phone_setting.show_code403 =
|
||
phone_setting.label_scroll_interval_time =
|
||
|
||
|
||
###Only T41P/T42G/T46G Models support this parameter
|
||
phone_setting.page_tip =
|
||
|
||
phone_setting.predial_autodial =
|
||
phone_setting.headsetkey_mode =
|
||
features.voice_mail_tone_enable =
|
||
##Except T19P/T21P Models support this parameter
|
||
phone_setting.reserve_certs_enable =
|
||
phone_setting.called_party_info_display.enable =
|
||
|
||
phone_setting.call_info_display_method =
|
||
## Only for T4X Models support this parameter
|
||
|
||
|
||
|
||
#######################################################################################
|
||
## Power Led Settings ##
|
||
#######################################################################################
|
||
phone_setting.common_power_led_enable =
|
||
phone_setting.talk_and_dial_power_led_enable =
|
||
phone_setting.mail_power_led_flash_enable =
|
||
phone_setting.ring_power_led_flash_enable =
|
||
phone_setting.mute_power_led_flash_enable=
|
||
phone_setting.hold_and_held_power_led_flash_enable =
|
||
|
||
##It configures the level of the active backlight intensity.
|
||
##For SIP-T28P IP phones and the connected EXP39:
|
||
##The default value is 2.
|
||
##For SIP-T46G IP phones and the connected EXP40:
|
||
##The default value is 8.
|
||
phone_setting.active_backlight_level =
|
||
|
||
##It configures the phone to go out or reduce intensity of the backlight on the LCD screen after a period of inactivity.
|
||
##0-Off,1-Low.
|
||
##The default value is 1.
|
||
phone_setting.inactive_backlight_level =
|
||
|
||
#######################################################################################
|
||
## Phone Setting Display ##
|
||
#######################################################################################
|
||
|
||
###Except T20P/T19P/T21P Models
|
||
##It configures the backlight time (in seconds).0, 1, 15, 30, 60, 120, 300, 600 or 1800.
|
||
phone_setting.backlight_time =
|
||
|
||
###Except T20P/T22P/T41P/T42G Models
|
||
###It configures the contrast of the LCD screen.
|
||
###For SIP-T19P and SIP-T21P IP phones, it configures the LCD<43><44>s contrast of the phone only.
|
||
###For SIP-T26P IP phones, it configures the LCD<43><44>s contrast of the connected EXP39 only.
|
||
###For SIP-T28P IP phones, it configures the LCD<43><44>s contrast of the IP phone and the connected EXP39.
|
||
###For SIP-T46G IP phones, it configures the LCD<43><44>s contrast of the connected EXP40 only.
|
||
###The default value is 6.
|
||
phone_setting.contrast =
|
||
|
||
###Except T46G Model
|
||
##It configures the logo mode of the LCD screen (except for SIP-T20P IP phones).
|
||
##For SIP-T19P/T21P/T22P/T26P/T41P/T42G IP phones:
|
||
##0-Disabled 1-System logo 2-Custom logo
|
||
##The default value is 0.
|
||
##For SIP-T28P IP phones:
|
||
##1-System logo 2-Custom logo
|
||
##The default value is 1.
|
||
##It enables or disables a text logo (for SIP-T20P IP phones).
|
||
##0-Disabled 1-Enabled
|
||
##The default value is 0.
|
||
phone_setting.lcd_logo.mode =
|
||
|
||
###Only T20P Model supports this parameter
|
||
##It configures a text logo.
|
||
##The default value is Yealink.
|
||
phone_setting.lcd_logo.text =
|
||
|
||
###Except T20P/T46G Models
|
||
lcd_logo.url =
|
||
lcd_logo.delete =
|
||
|
||
###Only T46G Model supports the two parameters
|
||
###It configures the wallpaper displayed on the phone.
|
||
###Example:To configure a phone built-in picture (e.g., 1.png) to be wallpaper, the value format is:
|
||
###phone_setting.backgrounds = Resource:1.png
|
||
###To configure a custom picture (e.g., custom1.png) to be wallpaper, the value format is: Config:custom1.png
|
||
###The default value is Resource:Default.jpg.
|
||
phone_setting.backgrounds =
|
||
|
||
wallpaper_upload.url =
|
||
|
||
#######################################################################################
|
||
## Phone Setting BLF ##
|
||
#######################################################################################
|
||
###It enables or disables the phone to automatically configure the BLF list keys in order.
|
||
###0-Disabled,1-Enabled.
|
||
###The default value is 1.
|
||
|
||
phone_setting.auto_blf_list_enable =
|
||
|
||
###Only T26P/T28P/T46G Models support the parameter
|
||
###It configures the order of BLF list keys assigned automatically.
|
||
###0-Line Keys->Memory Keys->Extension Keys
|
||
###1-Extension Keys->Memory Keys->Line Keys
|
||
###Memory keys are not applicable to SIP-T46G IP phones.
|
||
###The default value is 0.
|
||
phone_setting.blf_list_sequence_type =
|
||
|
||
#######################################################################################
|
||
## Key Lock ##
|
||
#######################################################################################
|
||
##Except T41P/T42G/T46G Models
|
||
phone_setting.lock =
|
||
|
||
###Only T41P/T42G/T46G Models support the two parameters
|
||
###It enables or disables keypad lock feature.
|
||
###0-Disabled,1-Enabled.
|
||
###The default value is 0.
|
||
phone_setting.phone_lock.enable =
|
||
|
||
###It configures the keypad lock type.
|
||
###0-All Keys,1-Function Keys,2-Menu Key.
|
||
###The default value is 0.
|
||
phone_setting.phone_lock.lock_key_type =
|
||
|
||
###It configures the password for unlocking the keypad.
|
||
###The default value is 123.
|
||
phone_setting.phone_lock.unlock_pin =
|
||
|
||
###It configures the interval (in seconds) to automatically lock the keypad.
|
||
###The default value is 0 (the keypad is locked only by long pressing the pound key or pressing the keypad lock key)
|
||
phone_setting.phone_lock.lock_time_out =
|
||
phone_setting.emergency.number =
|
||
|
||
#######################################################################################
|
||
## Multicast ##
|
||
#######################################################################################
|
||
|
||
###Except T19P Model
|
||
multicast.codec =
|
||
|
||
multicast.receive_priority.enable =
|
||
multicast.receive_priority.priority =
|
||
|
||
###X ranges from 1 to 10
|
||
###multicast.listen_address.X.label =
|
||
###multicast.listen_address.X.ip_address =
|
||
|
||
multicast.listen_address.X.label =
|
||
multicast.listen_address.X.ip_address =
|
||
###Except T19P/T21P Models support this parameter (<28><>X:1-10<31><30>)
|
||
|
||
multicast.paging_address.X.ip_address =
|
||
multicast.paging_address.X.label =
|
||
#######################################################################################
|
||
## Super Search(Except T20P Model) ##
|
||
#######################################################################################
|
||
super_search.recent_call =
|
||
super_search.url =
|
||
|
||
#######################################################################################
|
||
## Security ##
|
||
#######################################################################################
|
||
###Define the login username and password of the user, var and administrator.
|
||
###If you change the username of the administrator from "admin" to "admin1", your new administrator's username should be configured as: security.user_name.admin = admin1.
|
||
###If you change the password of the administrator from "admin" to "admin1pwd", your new administrator's password should be configured as: security.user_password = admin1:admin1pwd.
|
||
|
||
###The following examples change the user's username to "user23" and the user's password to "user23pwd".
|
||
###security.user_name.user = user23
|
||
###security.user_password = user23:user23pwd
|
||
###The following examples change the var's username to "var55" and the var's password to "var55pwd".
|
||
###security.user_name.var = var55
|
||
###security.user_password = var55:var55pwd
|
||
security.user_name.user =
|
||
security.user_name.admin =
|
||
security.user_name.var =
|
||
security.user_password =
|
||
|
||
###It enables or disables the phone to only accept the certificates in the Trusted Certificates list.
|
||
###0-Disabled,1-Enabled.
|
||
###The default value is 1.It takes effect after a reboot.
|
||
security.trust_certificates =
|
||
|
||
###It configures the source certificates for the phone to authenticate for TLS connection.
|
||
###0-Default certificates,1-Custom certificates,2-All certificates.
|
||
###The default value is 0.It takes effect after a reboot.
|
||
security.ca_cert =
|
||
|
||
###It configures the device certificates for the phone to send for TLS authentication.
|
||
###0-Default certificates,1-Custom certificates.
|
||
###The default value is 0.It takes effect after a reboot.
|
||
security.dev_cert =
|
||
|
||
###It enables or disables the phone to mandatorily validate the CommonName or SubjectAltName of the certificate received from the connecting server.
|
||
###0-Disabled,1-Enabled.
|
||
###The default value is 0.It takes effect after a reboot.
|
||
security.cn_validation =
|
||
|
||
security.trust_custom_certificates =
|
||
|
||
#######################################################################################
|
||
## User Mode ##
|
||
#######################################################################################
|
||
###It enables or disables the 3-level permissions (admin, user, var).
|
||
###0-Disabled,1-Enabled.
|
||
###The default value is 0.It takes effect after a reboot.
|
||
security.var_enable =
|
||
|
||
web_item_level.url =
|
||
|
||
#######################################################################################
|
||
## Trusted Certificates ##
|
||
#######################################################################################
|
||
trusted_certificates.url =
|
||
trusted_certificates.delete =
|
||
|
||
#######################################################################################
|
||
## Server Certificates ##
|
||
#######################################################################################
|
||
server_certificates.url =
|
||
server_certificates.delete =
|
||
|
||
#######################################################################################
|
||
## Memory Key(Only for T26P/T28P Models) ##
|
||
#######################################################################################
|
||
###T26P/T28P X ranges from 1 to 10
|
||
|
||
#memorykey.X.type--Customize the Memorykey type.
|
||
#The valid types are:
|
||
|
||
#0-NA 1-Conference 2-Forward 3-Transfer 4-Hold 5-DND 7-Call Return 8-SMS 9-Directed Pickup 10-Call Park 11-DTMF 12-Voice Mail 13-Speed Dial 14-Intercom
|
||
#15-Line 16-BLF 17-URL 18-Group Listening 20-Private Hold 22-XML Group 23-Group Pickup 24-Multicast Paging 25-Record 27-XML Browser
|
||
#34-Hot Desking 35-URL Record 38-LDAP 39-BLF List 40-Prefix 41-Zero Touch 42-ACD 45-Local Group 46-Network Group 49-Custom Button
|
||
#50-Keypad Lock 55-Meet-Me Conference 56-Retrieve Park 57-Hoteling 58-ACD Grace 59-Sisp Code 60-Emergency 61-Directory
|
||
|
||
###memorykey.X.line =
|
||
###memorykey.X.value =
|
||
###memorykey.X.pickup_value =
|
||
###memorykey.X.type =
|
||
###memorykey.X.xml_phonebook =
|
||
|
||
###It configures the desired line to apply the key feature.
|
||
###The default value is 1.Integer from 1 to 6
|
||
memorykey.1.line =
|
||
|
||
###It configures the value of the memory key feature.
|
||
###For example, when set the key feature to BLF, it configures the number of the monitored user.
|
||
###The default value is blank.
|
||
memorykey.1.value =
|
||
|
||
###It configures the pickup code for BLF feature or conference ID followed by the # sign for Meet-Me conference feature.
|
||
###It only applies to BLF and Meet-Me conference features.
|
||
###The default value is blank.
|
||
memorykey.1.pickup_value =
|
||
|
||
###It configures the desired feature for memory key X.
|
||
###The default value is 0.
|
||
memorykey.1.type =
|
||
|
||
###It configures the desired local group/XML group/network group for the memory key X.
|
||
###It only applies to the Local Group, XML Group and Network Group features.
|
||
###The default value is 0.
|
||
memorykey.1.xml_phonebook =
|
||
|
||
#######################################################################################
|
||
## Line Key ##
|
||
#######################################################################################
|
||
###Except T19D Model
|
||
###T21D/T20P X ranges from 1 to 2
|
||
###T22P/T26P X ranges from 1 to 3
|
||
###T28P X ranges from 1 to 6
|
||
###T41P/T42G X ranges from 1 to 15
|
||
###T46G X ranges from 1 to 27
|
||
|
||
#linekey.X.type--Customize the linekey type.
|
||
#The valid types are:
|
||
|
||
#0-NA 1-Conference 2-Forward 3-Transfer 4-Hold 5-DND 7-Call Return 8-SMS 9-Directed Pickup 10-Call Park 11-DTMF 12-Voice Mail 13-Speed Dial
|
||
#14-Intercom 15-Line 16-BLF 17-URL 18-Group Listening 20-Private Hold 22-XML Group 23-Group Pickup 24-Multicast Paging 25-Record 27-XML Browser
|
||
#34-Hot Desking 35-URL Record 38-LDAP 39-BLF List 40-Prefix 41-Zero Touch 42-ACD 45-Local Group 46-Network Group 49-Custom Button 50-Keypad Lock
|
||
#55-Meet-Me Conference 56-Retrieve Park 57-Hoteling 58-ACD Grace 59-Sisp Code 60-Emergency 61-Directory
|
||
|
||
#0-NA <20><>Only for T41/T42/T46)
|
||
#22-XML Group (Not support T20)
|
||
#38-LDAP (Not support T20)
|
||
#46-Network Group (Not support T20)
|
||
#8-SMS (Only support T21/T46/T22/T26/T28)
|
||
#17-URL (Only support T41/T42/T46)
|
||
#49-Custom Button (Only support T20/T22/T26/T28)
|
||
|
||
###linekey.X.line =
|
||
###linekey.X.value =
|
||
###linekey.X.pickup_value =
|
||
###linekey.X.type =
|
||
###linekey.X.xml_phonebook =
|
||
###linekey.X.label =
|
||
|
||
###It configures the desired line to apply the key feature.Integer from 1 to 6
|
||
linekey.1.line =
|
||
|
||
###It configures the value of the line key feature.
|
||
###For example, when setting the key feature to BLF, it configures the number of the monitored user.
|
||
###The default value is blank.
|
||
linekey.1.value =
|
||
|
||
###It configures the pickup code for BLF feature or conference ID followed by the # sign for Meet-Me conference feature.
|
||
###It only applies to BLF and Meet-Me conference features.
|
||
###The default value is blank.
|
||
linekey.1.pickup_value =
|
||
|
||
###It configures the key feature for the line key X.
|
||
linekey.1.type =
|
||
|
||
###It configures the desired local group/XML group/network group for the line key X.
|
||
###It only applies to the Local Group, XML Group and Network Group features.
|
||
###XML Group and Network Group features are not applicable to SIP-T20P IP phones.
|
||
linekey.1.xml_phonebook =
|
||
|
||
###It configures the label displayed on the LCD screen for each line key.
|
||
###The default value is blank.
|
||
linekey.1.label =
|
||
|
||
#######################################################################################
|
||
## Programable Key ##
|
||
#######################################################################################
|
||
###T20P X ranges from 1 to 9
|
||
###T28P/T26P X ranges from 1 to 14
|
||
###T41P/T42G/T19P/T21P X ranges from 1 to 11
|
||
###T46G/T22P X ranges from 1 to 13
|
||
|
||
#programablekey.x.type--Customize the programmable key type.
|
||
#The valid types are:
|
||
#0-NA 2-Forward 5-DND 7-Call Return 8-SMS 9-Directed Pickup 13-Speed Dial
|
||
#22-XML Group 23-Group Pickup 27-XML Browser 28-History 30-Menu 31-Switch Account 32-New SMS
|
||
#33-Status 34-Hot Desking 38-LDAP 40-Prefix 41-Zero Touch 43-Local Directory 44-Network Directory 45-Local Group
|
||
#46-Network Group 47-XML Directory 50-Keypad Lock 51-Switch Account Up 52-Switch Account Down 55-Meet-Me Conference 61-Directory
|
||
|
||
#40-Prefix (Not support T20)
|
||
#22-XML Group (Not support T20)
|
||
#31-Switch Account (Not support T19/T41/T42/T46)
|
||
#38-LDAP (Not support T19/T20)
|
||
#46-Network Group (Not support T20)
|
||
#8-SMS (Not support T41/T42/T20)
|
||
#32-New SMS (Not support T41/T42/T20)
|
||
#47-XML Directory (Not support T20)
|
||
#44-Network Directory (Not support T20)
|
||
#41-Zero Touch (Not support T41/T42/T46)
|
||
#34-Hot Desking (Only support T19/T46
|
||
#51-Switch Account Up (Only support T41/T42/T46)
|
||
#52-Switch Account Down (Only support T41/T42/T46)
|
||
|
||
###programablekey.X.type =
|
||
###programablekey.X.line =
|
||
###programablekey.X.value =
|
||
###programablekey.X.xml_phonebook =
|
||
###programablekey.X.history_type =
|
||
###programablekey.X.label =
|
||
###programablekey.X.pickup_value =
|
||
|
||
###It configures the key feature for the programmable key X.
|
||
programablekey.1.type =
|
||
|
||
###It configures the desired line to apply the programmable key feature.
|
||
programablekey.1.line =
|
||
|
||
###It configures the value of the programmable key feature.
|
||
###For example, when configuring the key feature to be Speed Dial, it configures the number.
|
||
###The default value is blank.
|
||
programablekey.1.value =
|
||
|
||
###It configures the desired local group/XML group/network group for the programmable key.
|
||
###It only applies to the Local Group, XML Group and Network Group features.
|
||
###XML Group and Network Group features are not applicable to SIP-T20P IP phones.
|
||
programablekey.1.xml_phonebook =
|
||
|
||
###It configures the history type of programmable key.
|
||
###0-Local History,1-Network History.
|
||
###The default value is 0.
|
||
programablekey.1.history_type =
|
||
|
||
###It configures the label displayed on the LCD screen for each soft key.
|
||
###The default value is blank.
|
||
programablekey.1.label =
|
||
|
||
###It configures conference ID followed by the # sign for Meet-Me conference feature.
|
||
###It only applies to Meet-Me conference feature.
|
||
###The default value is blank.
|
||
programablekey.1.pickup_value =
|
||
|
||
#######################################################################################
|
||
## Expansion Key(Only for T26P/T28P/T46G Models) ##
|
||
#######################################################################################
|
||
###T46G/T28P/T26P X ranges from 1 to 6, Y ranges from 1 to 40
|
||
|
||
###expansion_module.X.key.Y.type =
|
||
###expansion_module.X.key.Y.line =
|
||
###expansion_module.X.key.Y.value =
|
||
###expansion_module.X.key.Y.pickup_value =
|
||
###expansion_module.X.key.Y.label =
|
||
###expansion_module.X.key.Y.xml_phonebook =
|
||
|
||
###It configures the key feature of the expansion module X key Y.
|
||
expansion_module.1.key.1.type =
|
||
|
||
###It configures the desired line to apply the expansion module key feature.Integer from 1 to 6
|
||
expansion_module.1.key.1.line =
|
||
|
||
###It configures the value of the expansion module key feature.
|
||
###The default value is blank.
|
||
expansion_module.1.key.1.value =
|
||
|
||
###It configures the pickup code for BLF feature or conference ID followed by the # sign for Meet-Me conference feature.
|
||
###It only applies to BLF and Meet-Me conference features.
|
||
###The default value is blank.
|
||
expansion_module.1.key.1.pickup_value =
|
||
|
||
###It configures the label displayed on the LCD screen of the expansion module for each key.
|
||
###The default value is blank.
|
||
expansion_module.1.key.1.label =
|
||
|
||
###It only applies to the Local Group, XML Group and Network Group features.Integer from 0 to 48.
|
||
expansion_module.1.key.1.xml_phonebook =
|
||
|
||
#######################################################################################
|
||
## Forward Always ##
|
||
#######################################################################################
|
||
forward.always.enable =
|
||
forward.always.target =
|
||
forward.always.on_code =
|
||
forward.always.off_code =
|
||
|
||
#######################################################################################
|
||
## Forward Busy ##
|
||
#######################################################################################
|
||
forward.busy.enable =
|
||
forward.busy.target =
|
||
forward.busy.on_code =
|
||
forward.busy.off_code =
|
||
|
||
#######################################################################################
|
||
## Forward No Answer ##
|
||
#######################################################################################
|
||
forward.no_answer.enable =
|
||
forward.no_answer.target =
|
||
forward.no_answer.timeout =
|
||
forward.no_answer.on_code =
|
||
forward.no_answer.off_code =
|
||
|
||
#######################################################################################
|
||
## Forward International ##
|
||
#######################################################################################
|
||
###It enables or disables the phone to forward incoming calls to international numbers.
|
||
###0-Disabled,1-Enabled.
|
||
###The default value is 1.
|
||
forward.international.enable =
|
||
|
||
#######################################################################################
|
||
## ACD ##
|
||
#######################################################################################
|
||
acd.auto_available =
|
||
acd.auto_available_timer =
|
||
|
||
#######################################################################################
|
||
## Hotdesking Startup ##
|
||
#######################################################################################
|
||
phone_setting.logon_wizard =
|
||
##The default value is 1.Except T19P/T21P
|
||
features.auto_exit_logon_wizard.enable =
|
||
##############
|
||
hotdesking.startup_register_name_enable =
|
||
hotdesking.startup_username_enable =
|
||
hotdesking.startup_password_enable =
|
||
hotdesking.startup_sip_server_enable =
|
||
hotdesking.startup_outbound_enable =
|
||
|
||
#######################################################################################
|
||
## Hotdesking Dsskey ##
|
||
#######################################################################################
|
||
hotdesking.dsskey_register_name_enable =
|
||
hotdesking.dsskey_username_enable =
|
||
hotdesking.dsskey_password_enable =
|
||
hotdesking.dsskey_sip_server_enable =
|
||
hotdesking.dsskey_outbound_enable =
|
||
|
||
#######################################################################################
|
||
## Alert Info ##
|
||
#######################################################################################
|
||
###X ranges from 1 to 100
|
||
###distinctive_ring_tones.alert_info.x.text =
|
||
###distinctive_ring_tones.alert_info.x.ringer =
|
||
|
||
###It configures the internal ringer text for distinctive ringtone.
|
||
###Example: distinctive_ring_tones.alert_info.1.text = Family
|
||
###The default value is blank.
|
||
distinctive_ring_tones.alert_info.1.text =
|
||
|
||
###It configures the desired ring tones for each text.
|
||
###The value ranges from 1 to 8, the digit stands for the appropriate ringtone.
|
||
###Ring tones 6-8 are only applicable to SIP-T46G IP phones.
|
||
###The default value is 1.
|
||
distinctive_ring_tones.alert_info.1.ringer =
|
||
|
||
#######################################################################################
|
||
## Call Waiting ##
|
||
#######################################################################################
|
||
call_waiting.enable =
|
||
call_waiting.tone =
|
||
call_waiting.on_code =
|
||
call_waiting.off_code =
|
||
|
||
#######################################################################################
|
||
## Action URL ##
|
||
#######################################################################################
|
||
action_url.setup_completed =
|
||
action_url.registered =
|
||
action_url.unregistered =
|
||
action_url.register_failed =
|
||
action_url.off_hook =
|
||
action_url.on_hook =
|
||
action_url.incoming_call =
|
||
action_url.outgoing_call =
|
||
action_url.call_established =
|
||
action_url.dnd_on =
|
||
action_url.dnd_off =
|
||
action_url.always_fwd_on =
|
||
action_url.always_fwd_off =
|
||
action_url.busy_fwd_on =
|
||
action_url.busy_fwd_off =
|
||
action_url.no_answer_fwd_on =
|
||
action_url.no_answer_fwd_off =
|
||
action_url.transfer_call =
|
||
action_url.blind_transfer_call =
|
||
action_url.attended_transfer_call =
|
||
action_url.hold =
|
||
action_url.unhold =
|
||
action_url.mute =
|
||
action_url.unmute =
|
||
action_url.missed_call =
|
||
action_url.call_terminated =
|
||
action_url.busy_to_idle =
|
||
action_url.idle_to_busy =
|
||
action_url.ip_change =
|
||
action_url.forward_incoming_call =
|
||
action_url.reject_incoming_call =
|
||
action_url.answer_new_incoming_call =
|
||
action_url.transfer_finished =
|
||
action_url.transfer_failed =
|
||
action_url.setup_autop_finish =
|
||
action_url.held =
|
||
action_url.unheld =
|
||
|
||
|
||
|
||
#######################################################################################
|
||
## Contact ##
|
||
#######################################################################################
|
||
local_contact.data.url =
|
||
###(Only T48G Model supports the parameter)
|
||
local_contact.image.url =
|
||
local_contact.icon.url =
|
||
|
||
###(Only T46G Model supports the parameter)
|
||
local_contact.data_photo_tar.url =
|
||
|
||
###(Except T20P Model)
|
||
directory_setting.url =
|
||
## Except T19P/T21P Model supports the parameter
|
||
directory.edit_default_input_method =
|
||
directory.search_default_input_method =
|
||
phone_setting.dsskey_directory_auto.enable =
|
||
|
||
#######################################################################################
|
||
## Custom Factory Configuration ##
|
||
#######################################################################################
|
||
custom_factory_configuration.url =
|
||
features.custom_factory_config.enable =
|
||
|
||
#######################################################################################
|
||
## Custom Configuration ##
|
||
#######################################################################################
|
||
configuration.url =
|
||
|
||
#######################################################################################
|
||
## Custom Softkey(Except T20P Model) ##
|
||
#######################################################################################
|
||
phone_setting.custom_softkey_enable =
|
||
custom_softkey_call_failed.url =
|
||
custom_softkey_call_in.url =
|
||
custom_softkey_connecting.url =
|
||
custom_softkey_dialing.url =
|
||
custom_softkey_ring_back.url =
|
||
custom_softkey_talking.url =
|
||
|
||
#######################################################################################
|
||
## Custom Input Method ##
|
||
#######################################################################################
|
||
gui_input_method.url =
|
||
|
||
#######################################################################################
|
||
## Configure the access URL of firmware ##
|
||
#######################################################################################
|
||
###It configures the access URL of the firmware file.
|
||
###The default value is blank.It takes effect after a reboot.
|
||
firmware.url =
|
||
|
||
#######################################################################################
|
||
## RTCP ##
|
||
#######################################################################################
|
||
###(Except T23 Model)
|
||
phone_setting.rtcp_xr_report.enable =
|
||
phone_setting.vq_rtcpxr.interval_report.enable =
|
||
phone_setting.vq_rtcpxr.session_report.enable =
|
||
phone_setting.vq_rtcpxr.states_show_on_gui.enable =
|
||
phone_setting.vq_rtcpxr.states_show_on_web.enable =
|
||
phone_setting.vq_rtcpxr_delay_threshold_critical =
|
||
phone_setting.vq_rtcpxr_delay_threshold_warming =
|
||
phone_setting.vq_rtcpxr_display_jitter.enable =
|
||
phone_setting.vq_rtcpxr_display_jitter_buffer_max.enable =
|
||
phone_setting.vq_rtcpxr_display_local_call_id.enable =
|
||
phone_setting.vq_rtcpxr_display_local_codec.enable =
|
||
phone_setting.vq_rtcpxr_display_moscq.enable =
|
||
phone_setting.vq_rtcpxr_display_moslq.enable =
|
||
phone_setting.vq_rtcpxr_display_packets_lost.enable =
|
||
phone_setting.vq_rtcpxr_display_remote_call_id.enable =
|
||
phone_setting.vq_rtcpxr_display_remote_codec.enable =
|
||
phone_setting.vq_rtcpxr_display_round_trip_delay.enable =
|
||
phone_setting.vq_rtcpxr_display_start_time.enable =
|
||
phone_setting.vq_rtcpxr_display_stop_time.enable =
|
||
phone_setting.vq_rtcpxr_display_symm_oneway_delay.enable =
|
||
phone_setting.vq_rtcpxr_interval_period =
|
||
phone_setting.vq_rtcpxr_moslq_threshold_critical =
|
||
phone_setting.vq_rtcpxr_moslq_threshold_warming =
|
||
#######################################################################################
|
||
## Reboot ##
|
||
#######################################################################################
|
||
auto_provision.reboot_force.enable =
|
||
|
||
#######################################################################################
|
||
## Call Display ##
|
||
#######################################################################################
|
||
phone_setting.called_party_info_display.enable =
|
||
phone_setting.call_info_display_method =
|
||
##(Except T23 Model)
|
||
phone_setting.contact_photo_display.enable =
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|